·Dimmable built-in and independent constant current tunable white LED driver
·Dimming range 1~100 %
·DC 36V rated input
·Max.output power 53.6W
·30-33.5V output
·Integrated DALI PSU,14V 50mA (isolated)
·Low standby power
·Upto 94%eficiency(DALI PSU shutdown)
·Start time<0.6s
·Dual channel tunable white output
·Flicker free
·DiiA/Zhaga connectivity extensions DT49,DT50,DT51,DT52
·Output current programmable between 1000 -1600 mAvia DALI or UART
·Nominal life-time is more than 50,000 hours

・The max. output current is fixed: 200mA / 100mA /
    50mA (optional).
・Input and output are Double isolated.
・Output short circuit protection.
・Low standby power consumption.
・IP24 protection rating.
・AC input voltage range: 100~277Vac.
・Compact form factor and thin profile (easy to fit into
    lamp casing, wall switch box etc.).
・5 year Warranty.
・Operating temperature range: -40 ~ +75 °C.

・non-SELV-SELV.
・HVLED and LVLED output are more convenient to use.
・Adjustable light intensity.
・Adjustable output current via DALI.
・Dimming range 1-100% .
・Metering data can be read out through DALI interface.
・For luminaire of protection class I and protection class II.
・Nominal life-time up to 100,000H.
・5-years guarantee.

It can measure power and internal temperature.
・Can convert 0－10V dimming signal or digital dimming commands
    into DALI broadcast command.
・2 CHs 0-10V dimming signals or digital dimming commands
    are buffered output.
・0-10V output interfaces are designed to sink or source current up
    to 25mA.
・Digital command or 0-10V signal dimming method can be selected
    through ESI.
・DALI 2-wire sensor (highest priority) and ESI sensor supported.
・The data can be read by ESI or DALI port.
・DiiA/Zhaga connectivity extensions DT49, DT50, DT51, DT52.
・Selection of the desired device type via operating mode;
    0x00: IEC 62386-102 standard mode.
    0x80: manufacturer specific mode, DT6, DT8 Tc, DT17
    supported (default).
・Translate DALI dimming commands to 2 CHs analog 0-10V output
    (ChA: Intensity, ChB: CCT).
・The AC load relay can be switched off when dimming off.
・AC load relay will switch off AC output when dimming level is set
    to 0.
・Zero-crossing switching function for AC load relay.
・DC signal relay will short-circuit DALI interface and physically
    disconnect 0-10V output interfaces in case of power loss.
・Built-in DALI PSU, 15V, 55mA (programable to 200mA)
・Built-in ESI PSU, 15V, 50mA.
・AC output: 8A Max., 1385VA Max.
・Over current protection when load connects to Switched, and the
    failure information is recorded in NVM
・DALI / 0-10V and ESI interfaces are both compliant with SELV.
・Communication protocol compatible with Enlighted Sensor
    Interface [ESI] Definition Rev 4.8 .

Product description
・Emergency lighting load control relays.
・Conforms To UL STD 924.
・Operating Voltage: 100Vac to 277Vac / 140Vdc to 390Vdc.
・Operating Temperature: -25℃ to +70℃.
・Built-in DALI PSU, 15V / 200mA .

Emergency Load Relay Specification
・One (1) SPDT Continuous Duty Coil.
・1 Million Cycles Minimum Mechanical Lifetime.
・Operate Time: 15mS.
・Maximum Switching Load Voltage: 347Vac / 300Vdc.
・Maximum Switching Load current: 8A Max.
・Maximum Switching Load power: 1385VA Max.

Signal Relay Specification
・One (1) SPDT Continuous Duty Coil.
・1 Million Cycles Minimum Mechanical Lifetime.
・Operate Time: 3mS.
・Maximum Switching Load Voltage: 250Vac / 30Vdc.
・Maximum Switching Load Current: 1A.