Carbon monoxide cannot be felt, seen or smelled .... but fortunately it can be measured.

This life-threatening and invisible gas is produced by any combustion in which there is not enough oxygen - which is a growing risk due to our increasingly well insulated buildings.
As you cozy up in front of the fireplace and relax, gazing into the warming flames, carbon monoxide can build up in the room. This carbon monoxide is also produced by other combustible materials, such as pellets, paper, cardboard or even gases such as butane, propane, methane and oil.

Then, if not well ventilated, we inhale this gas.
The problem is that our body does not recognize the carbon monoxide, but binds its molecules to the red blood cells like oxygen. But our cells need pure oxygen, they can't do anything with the carbon monoxide, unfortunately exhaling the CO doesn't work either and so we accumulate the carbon monoxide in our body - and have less and less free red blood cells to transport the vital oxygen into the cells. So we suffocate - even though we breathe.

That's why a CO detector is truly a life-saving investment in your safety.

Our GX-C300 is a professional carbon monoxide warning system for fixed installation with internal electro-chemical CO sensor that detects precise values from 0-330ppm CO concentration.  The display of the precisely measured CO concentration in ppm is shown on the illuminated plain text display with powerful 32bit microcontroller. In case of alarm by the integrated, loud piezo, as well as flashing display and in case of technical faults detected by the device itself, a potential-free change-over relay switches in each case, e.g. to activate forced ventilation or to inform the building management system. 
The gas warning system is factory set with warning levels and alarm delay times as in standard DIN EN 50291, but these can be changed according to your specifications. Please contact our technical support.
The internal electrochemical sensor has a lifetime of 6 to 10 years depending on the environmental conditions. The service of Elektrotechnik Schabus offers the exchange in the factory.

Item number: 300255

EAN: 4044764004115

Possible applications
Monitoring of combustion places / gas heaters in case of carbon monoxide (CO) leakage
Monitoring of guest rooms in shisha bars and smoking clubs
monitoring of staircases and escape routes in small private underground garages
open fireplaces in restaurants, canteens and mobile kitchens
heating and utility rooms as well as all dry indoor rooms with combustion sites

Performance features
acoustic and optical warning
high-precision CO measurement and ppm-accurate display
2 potential-free change-over relays 5 A, one each for alarm and fault, perfect for building management systems
intelligent sensor system to avoid false alarms
continuous monitoring, storage and display of operating parameters in plain text display
shutdown of the source of danger in case of alarm
integrated switching power supply for low power consumption

Technical data
operating voltage: 110 ... 240 V~ / 50-60 Hz
power consumption: approx. 2-8 VA, depending on operating condition
Relay contacts: change-over NC/NO (potential-free)
Switching capacity alarm: max. 5 A / 230 V~
Switching capacity fault: max. 5 A / 60 V=
all connections: screw terminals
Display: 2x 16 characters LCD, illuminated, white-blue
Display LEDs: green operation, yellow fault, red alarm
CO sensor, technology: internal, electrochemical
CO concentration: 0 ... 330ppm, triggering according to standard
CO sensor lifetime max.: 6 years (max. 40°C, min. 40% rH) - 10 years (max. 28°C, min. 30% rH)
CO triggering standard: 50 ppm - 60 minutes
100 ppm - 10 minutes
300 ppm - immediate
Accuracy: < ±1% / < ±2ppm, factory calibrated
Sound pressure internal piezo: 85dB(A) @ 1 m distance
Operating range: -10 °C / +50 °C
Humidity: 10 ... 90 % rH, non-condensing
Protection class: IP20 (IP65 available on request)
Dimensions (HxWxD): 80 x 160 x 55 mm

Not in the mood for office air?

In the hectic office routine, you often notice it too late - many different factors cause the proverbial "thick air".

Our oxygen supply continuously decreases and we become flabby and tired.

Fresh air means more oxygen - thus more well-being and more efficiency.

The CO2 traffic light "office" supports you to ventilate in time, to ventilate for a sufficient
long enough and thus to ventilate in a sensible, energy-saving way.
This way you will quickly feel fit again - and that is logically also healthier.

Green light for the working atmosphere

The CO2 traffic light "office" is not only available in white, but also in green or gray - or painted in your RAL color on request.

The enclosed wall bracket is mounted on a wall as far away as possible from the nearest window / door at a height of 1.8 - 2 meters and the power supply unit with its 2.3 meter long supply cable is plugged into a socket. After a warm-up phase of three minutes, the CO2 traffic light "office" is ready for operation.

Alternatively, you can order the stand and mount the traffic light on a horizontal surface - always clearly visible.

As soon as the CO2 traffic light "office" is yellow (from 1200 ppm) open a window and ventilate until the traffic light is green again.

Often airing is too short, too long or too often, which causes unnecessary heating or air conditioning costs.

At night, the LED lights dim automatically, which is why the "office" CO2 traffic light is particularly energy-saving.

especially low energy costs - due to the long-life LED lights with automatic night dimming

10 years manufacturer warranty - quality made in Germany

Item number: 400380

EAN: 4044764004696

Technical data:
Operating voltage: 12 V DC from enclosed plug-in power supply unit.
supply line traffic light / power supply unit: approx. 80 cm / approx. 150 cm
Protection class: IP 20, IP54 possible on request
Sensor type: NDIR infrared, internal
trigger concentrations: approx. 1200 ppm yellow / 2000 ppm red
highest trigger concentration: approx. 2500 ppm red flashing with alarm tone
Functional range sensor: +5°C / +45°C
Humidity (ambient): 5-90% RH (non-condensing)
Illuminant: long-life LEDs
dimensions (HxDxD): 303 x 55 x 80 mm

Scope of delivery: CO2 traffic light with 0.8 m supply cable, 12 V plug-in power supply unit with 1.5 m cable, wall mounting set with screws and dowels, detailed German operating instructions

Checked ice cold - 
If you want to know immediately and reliably whether gases are escaping from your plant, you need the appropriate sensors. The GX-CFC sensor can detect typical combustible gases such as methane, butane, propane and ethanol. 
However, it is also fully functional down to an ambient temperature of -20°C, the monitored air should be as dry as possible (<40% rH).
This makes the GX-CFC (climate fluorocarbon) ideal for monitoring refrigerants, i.e. the detection of many fluorinated hydrocarbons of the R-group, its target gas is R-32. 

Contact our technical support if you need to detect a HFC refrigerant that is not listed here.

Features
    External sensor for GX-A1+ , GX-HS and GX-C300S gas detectors
    Detection of R-22, R-32, R-404a, R-407c, R-410a, R-1234yf, ...
    Climate Fluoro Carbons are fluorinated refrigerants used in air conditioning and refrigeration equipment.

The external sensor is connected to the cable via a RJ connector. The connecting cable of the sensor can be extended.
The following minimum cross-sections result depending on the length of the cable:
Cable cross section 3 x 0.75 mm²: maximum length 10 m
Cable cross section 3 x 1.5 mm²: maximum length 20 m

Item number: 200901

EAN: 4044764004177

Technical data
operating voltage: 5 V
sensor type: catalytic
concentration: approx. 100 ppm to 3,000 ppm typical, depending on gas, up to max. 10,000 ppm
highest sensitivity: R1234yf
Humidity (ambient): 5-90 % vH (non-condensing)
operating range: -20°C / +40°C / optimum +20°C
storage temperature: -20°C / +70°C
Lifetime: approx. 5 years
Protection class: IP 20
Cable length: 2,5 m
Cable Ø: 3,5 mm
Dimensions (HxWxD): 52x27x29 mm 

Always this pressure ...
in the safe and proper handling of gas cylinders. Whether CO2 has escaped through your CO2 gas cylinder, e.g. for the water bubbler or at leaky fittings, you can measure comfortably with our GX-D500P. 

Other areas of application are dry ice processing and storage, occupational safety, food refrigeration e.g. of meat and sausage products, beverage dispensing systems, greenhouses with CO2 fumigation and overall thermally demanding rooms with very hot, cold, humid or dusty air or in ventilation systems with drafts.

The GX-D500P is a carbon dioxide warning device with ppm-accurate measurement and display of CO2 concentration in tenths of a percent, as well as display and storage of many operating parameters on a plain text display. The NDIR infrared sensor with high lifetime is permanently monitored by two µControllers and provides precise results.
The room to be monitored is connected to the device via a silicone hose, and a fan wheel ensures accelerated diffusion of the CO2 to the internal CO2 sensor. At the same time, unfavorable temperatures in the outside hose section adapt to the ambient temperature of the warning device.
2 potential-free change-over relays switch in case of alarm (3%) and in case of technical faults detected by the device itself.
The warning concentrations have been set at 1.5% and 3.0% in accordance with the TRGS for CO2 from beverage dispensing systems, but can also be parameterized alternatively by Elektrotechnik Schabus in the factory at the customer's request.
The application of the GX-D500P is always technical, be it the monitoring of CO2 bottles or the processing of dry ice.

Item number: 300263
EAN: 4044764004467

Performance features
monitoring of thermally demanding rooms with very warm, cold, humid or dusty air
suitable for CO2 from technical plants under pressure
suitable for dry ice processing / storage
relay contact for automatic ventilation
acoustic and optical warning
second relay for fault messages to the building control system
calibration possibility (zero point) for user
plain text display with indication of CO2 concentration
pre-alarm stage 1.5% CO2 / main alarm at 3% CO2 following the monitoring of beverage dispensing systems
internal NDIR sensor and connection of the room to be monitored by means of silicone hose

Technical data
operating voltage: 230 V~ (+/- 10%) / max. 8 VA
power consumption: max. 10 VA, depending on operating condition
Relay contacts: 2 potential-free change-over relays
Relay Re1 "Alarm": 250 V~ AC / 5 Amps max.
Relay Re2 "Fault": 60 V= DC / 5 Amps max.
Piezo alarm transmitter Sound pressure: approx. 85dB(A) @ 1 meter
Trigger concentrations: 1.5% / 15,000 ppm pre-alarm // 3.0% / 30,000 ppm main alarm
Sensor technology: optical, infrared absorption, NDIR
Display: 2x 16 Z. Display: white/blue, illuminated, flashes on alarm
3x LED: green operation, yellow error, red alarm
Function range: 0°C ... +45°C for control unit
silicone hose: 6/10mm, 2m enclosed, max. 4m
Protection class control unit:    IP20 (IP65 on request against surcharge)
Dimensions (HxWxD): 80 x 160 x 55 mm

With rubber boots through the puddles -. 
that can sometimes even be fun. But please not at home.

That's why SCHABUS offers high-quality sensors - and of course the right water detectors.

Our latest development is the ball-electrode water sensor SHT 5090, which, due to its own weight of around 100 grams, lies flat on the floor without further installation. Ideal on floors that must not be drilled into.

Even if you place the sensor vertically in narrow angles - e.g. under the radiator, under dishwashers and washing machines or simply under the shower tray cavity - at least 2 contacts always touch the floor and reliably trigger the alarm on the water alarm system in the event of water penetration.

Completely without mounting or fixing the sensor!

Sensor for connection to water detection system SHT 5000 or SHT 5001 and as overflow detector for SHT 5002

Article number: 300721

EAN: 4044764004641

Technical data
Max. Height horizontal = ball diameter 20 mm
Electrode distance 43 mm
Minimum conductivity horizontal: 30 µS
Minimum conductivity standing: 60 µS
Cable length 2.5 meters (special lengths on request)
Cable 2x 0.14 mm² - LiYY -Ø 3.2 mm
Dimensions horizontal without cable (Ø x H) 70 x 20 mm
Weight approx. 100 gram
electrode material V2A stainless steel, bright turned
no assembly, simply lay down