VEmesh E2D Zhaga Bridge’s functionality is basically similar to VEmesh E2D Bridge Node. Its form factor has been designed according to Zhaga book 18 standard, for fast installation and additional interchangeability in street lighting with DALI luminaires and sensors.


TECHNICAL SPECIFICATIONS
• Water and dust sealing standard: IP 20
• Unit size in millimeters: 27.40 x 80.00 x 115.10 - Rergular
• Possible address numbers from one unit to 16,000
• Wireless operation range from the first unit: 300 m
• Frequency range: 915-917 MHz
• Communication protocols: MODBUS, E2D
• Communication type: Encrypted radio

VEmesh D2D (DALI to DALI) Bridge Node is a family of VEmesh network devices that are part of Wireless Extension to DALI (D2D) solution. These networks add wireless capability to regular DALI (wired), thus increasing your productivity of lighting control deployment, lowering the maintenance costs and enabling you to operate in places that otherwise would be difficult to access. You can keep using all you existing DALI luminaires, drivers, controllers, sensors, and other DALI devices as is, eliminating your need to invest in dedicated wireless DALI products. As such, D2D is a simple and intuitive solution for replacing wires by wireless, where needed or in all DALI network.
In a VEmesh D2D Network, the connection of the DALI devices is through VEmesh D2D Bridge Nodes. Up to 64 x D2D Bridge Nodes and 1 x D2D Gateway form together a VEmesh D2D network for high performance and cost-effective wireless DALI connectivity. Each VEmesh Bridge Node can support up to 64 DALI short addresses of control gear, such as LED Drivers. In addition, you can use D2D Nodes to connect to switches, presence detectors and sensors with application controllers for DALI and various extensions to the leading suppliers of standard DALI products on the market.
VEmesh D2D supports simultaneous operation of up to 250 D2D Networks in the same or adjacent location, for large lighting systems. The configuration for multi-network systems uses the D2D Toolkit.
For additional information, please check our website at http://www.virtual-extension.com/products/d2d-products/

VEmesh D2D Bridge Node is designed to operate with devices complying with DALI1 and DALI2 (IEC 62386 relevant parts).
All VEmesh products use synchronized-flooding technology for utmost wireless performance, including space diversity and time diversity for highest propagation robustness. They also use Frequency Hopping, which in Europe employs LBT and AFA for maximum transmission power and range. The supported RF wireless regulations are of Europe, North America, South America and Israel, depending on the model.
VEmesh D2D Bridge Node has an Internal Antenna for improved cost-effectiveness; external antenna is an option.

An E2D system comprises one VEhub (or customer’s CMS), up to 250 VEmesh E2D wireless networks. Each network requires one Gateway, and can support any number of Bridges for up to 16,000 devices, such as luminaires or sensors.

On the RF side, a VEmesh network comprises of one VEmesh E2D Gateway and a number of Nodes. The VEmesh Bridges are the Nodes of an E2D Network.

On the DALI side, each VEmesh Bridge connects to one or more standard DALI devices or sensors, with a VEmesh Bridge capable to support up to 4 such devices – either on a pole for streetlighting or in a building. The Bridge actually forms a DALI loop, with the connection following DALI standard IEC 62386.

Through this connection, the Bridge receives all DALI signals from the DALI devices that it is connected (such as LED drivers replies and input devices’ events), and forwards them to the VEmesh wireless network. In the opposite direction, the VEmesh Bridge receives the DALI Master commands and forwards them on its DALI loop to the devices that it is connected.

One E2D Bridge supports 1 to 4 devices and it does not require a DALI address of its own.

The Bridge has a plastic case and its dimensions are 149.5mm x 40mm x 28.1mm (5.89” x 1.57” x 1.1”).

The wireless unit control “VE NEMA” connects through 7 pins, with a quick and standard connection to the lighting fixture.

TECHNICAL SPECIFICATIONS

• Dust and water resistance standard: IP 65
• Unit diameter in mm: 84-86 mm
• Number of possible addresses per unit - one single unit
• Wireless operating range: approximately 300 meters between units, MESH technology
• Frequency range - 915-917 MHz
• Operation and control capabilities - DALI 1 and DALI 2 • Communication type - Encrypted RF
• Operating temperature - From minus 40 to plus 80

KEY POINTS:

• No additional communication provider costs
• 10 years warranty at VE's service center
• Units can be connected to VE's control system or the municipality's control system using an open protocol (API VE)
• Up to 16,000 units can be connected to a single controller
• Wireless software updates available as an option
  
  

  The unit will connect to the designated socket in each lamp.

  A central requirement for installing this unit: a 'DALI' driver in the

  lighting fixture."

VEmesh E2D Zhaga Bridge’s functionality is basically similar to VEmesh E2D Bridge Node. Its form factor has been designed according to Zhaga book 18 standard, for fast installation and additional interchangeability in street lighting with DALI luminaires and sensors.


TECHNICAL SPECIFICATIONS
• Water and dust sealing standard: IP 20
• Unit size in millimeters: 27.40 x 80.00 x 115.10 - Rergular
• Possible address numbers from one unit to 16,000
• Wireless operation range from the first unit: 300 m
• Frequency range: 915-917 MHz
• Communication protocols: MODBUS, E2D
• Communication type: Encrypted radio

VEmesh D2D (DALI to DALI) Bridge Node is a family of VEmesh network devices that are part of Wireless Extension to DALI (D2D) solution. These networks add wireless capability to regular DALI (wired), thus increasing your productivity of lighting control deployment, lowering the maintenance costs and enabling you to operate in places that otherwise would be difficult to access. You can keep using all you existing DALI luminaires, drivers, controllers, sensors, and other DALI devices as is, eliminating your need to invest in dedicated wireless DALI products. As such, D2D is a simple and intuitive solution for replacing wires by wireless, where needed or in all DALI network.
In a VEmesh D2D Network, the connection of the DALI devices is through VEmesh D2D Bridge Nodes. Up to 64 x D2D Bridge Nodes and 1 x D2D Gateway form together a VEmesh D2D network for high performance and cost-effective wireless DALI connectivity. Each VEmesh Bridge Node can support up to 64 DALI short addresses of control gear, such as LED Drivers. In addition, you can use D2D Nodes to connect to switches, presence detectors and sensors with application controllers for DALI and various extensions to the leading suppliers of standard DALI products on the market.
VEmesh D2D supports simultaneous operation of up to 250 D2D Networks in the same or adjacent location, for large lighting systems. The configuration for multi-network systems uses the D2D Toolkit.
For additional information, please check our website at http://www.virtual-extension.com/products/d2d-products/

VEmesh D2D Bridge Node is designed to operate with devices complying with DALI1 and DALI2 (IEC 62386 relevant parts).
All VEmesh products use synchronized-flooding technology for utmost wireless performance, including space diversity and time diversity for highest propagation robustness. They also use Frequency Hopping, which in Europe employs LBT and AFA for maximum transmission power and range. The supported RF wireless regulations are of Europe, North America, South America and Israel, depending on the model.
VEmesh D2D Bridge Node has an Internal Antenna for improved cost-effectiveness; external antenna is an option.

An E2D system comprises one VEhub (or customer’s CMS), up to 250 VEmesh E2D wireless networks. Each network requires one Gateway, and can support any number of Bridges for up to 16,000 devices, such as luminaires or sensors.

On the RF side, a VEmesh network comprises of one VEmesh E2D Gateway and a number of Nodes. The VEmesh Bridges are the Nodes of an E2D Network.

On the DALI side, each VEmesh Bridge connects to one or more standard DALI devices or sensors, with a VEmesh Bridge capable to support up to 4 such devices – either on a pole for streetlighting or in a building. The Bridge actually forms a DALI loop, with the connection following DALI standard IEC 62386.

Through this connection, the Bridge receives all DALI signals from the DALI devices that it is connected (such as LED drivers replies and input devices’ events), and forwards them to the VEmesh wireless network. In the opposite direction, the VEmesh Bridge receives the DALI Master commands and forwards them on its DALI loop to the devices that it is connected.

One E2D Bridge supports 1 to 4 devices and it does not require a DALI address of its own.

The Bridge has a plastic case and its dimensions are 149.5mm x 40mm x 28.1mm (5.89” x 1.57” x 1.1”).